Try Updated Cisco 200-601 Exam Questions – [Dec-2017 Dumps]
The success in Cisco Certified Network Associate Industrial 200-601 certification exam is very easy . Your success will give you a lot more in form of your professional development in Network Application Development,Network Services and Cisco Industrial Networking. The Cisco 200-601 exam practice test software comes with money back guarantee, if you fail in the 200-601 exam, you will not be at risk of losing your money at all. We at, CCNABraindumps provide you most latest and actual 200-601 exam questions.
Refer to the exhibit.
Which two parameters can be used to diagnose an overloaded system? (Choose two)
A. Ethernet Port 1 Speed
B. Module Resource Allocation Actual Rate
C. Class 3 Received bytes per second
D. Media Counters Alignment Errors
E. TCP Connections Active
Answer: B, E
Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch?
A. switch#show snooping ip igmp
B. switch#show igmp snooping
C. switch#show ip igmp snooping
D. switch#show ip snooping
New Updated 200-601 Exam Questions 200-601 PDF dumps 200-601 practice exam dumps: https://www.dumpsschool.com/200-601-exam-dumps.html (70 Questions)
Refer to the exhbit. Which three elements would enable high availability and predictable performance for a motion control application spread across two switches (with video and I/O traffic)? (Choose three)
A. Configure QoS to give PTP traffic the highest priority
B. Fiber optic uplinks
C. Redundant uplinks
D. Configure QoS to give I/O traffic the highest priority
E. Copper uplinks
F. Interconnect the two switches
Answer: A, B, C
You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?
A: Lattency and Jitter
B: Redundancy and high availability
C: Explicit and Implicit messaging
D: This cycle time is not possible on an Ethernet network
E: Gigabit port speed
Refer to the exhibit.
CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1. You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in:
L2SW4# show mls interface GigabitEthernet 1/1 statistics
A. Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue
B. Increase the buffer allocation for input queue 1
C. Increase the buffer allocation for output queue 1
D. Alter the service policy to police to a higher CIR
E. Change the egress queue map on L2SW4 to map this traffic to a less congested queue
Answer: C, E
It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as opposed to the Enterprise where it is not generally deployed. What are two reasons why REP is more suitable for the plant floor? (Choose two)
A. REP is only supported on Industrial Ethernet switches, it is not supported on Catalyst switches.
B. REP converges faster than Spanning Tree, allowing for greater network availability.
C. REP supports Industrial Ethernet protocols better because it moves the packets faster.
D. Running dual cables from access switches to an aggregation switch can have a much higher cost on the plant floor than in the Enterprise and running a ring protocol like REP provides resiliency at a lower cost.
E. Industrial protocols can be negatively impacted by the number of nodes the Ethernet frame traverses, REP provides a topology with no more than 3 nodes for any data path.
Answer: B, D