Try Updated Juniper JN0-661 Exam Questions – [Feb-2018 Dumps]
The success in Juniper Service Provider Routing and Switching JN0-661 certification exam is very easy . Your success will give you a lot more in form of your professional development in Routing and Switching Services,Wireless Configuration and Service Provider Routing and Switching. The Juniper JN0-661 exam practice test software comes with money back guarantee, if you fail in the JN0-661 exam, you will not be at risk of losing your money at all. We at, CCNABraindumps provide you most latest and actual JN0-661 exam questions.
♥ VALID JN0-661 Exam Questions 2018 ♥
JN0-661 exam questions, JN0-661 PDF dumps; JN0-661 exam dumps:: https://www.dumpsschool.com/JN0-661-exam-dumps.html (133 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)
Latest and Most Accurate Juniper JN0-661 Dumps Exam Questions and Answers:
As a network administrator, you are asked to configure the VPN-B routing instance so that P routers are masked in CE2-to-CE5 trace routes For the VPN-A routing instance. P routers should appear in CE1-to-CE4 trace routes
Referring to the exhibit, which two actions achieve this task? (Choose two)
Referring to the exhibit, which two actions achieve this task? (Choose two.)
A. Add the no-vrf-propagate-ttl statement to the VPN-B routing instance on PE1.
B. Add the no-vrf-propagate-ttl statement on egress router PE2.
C. Add the no-vrf-propagate-ttl statement on transit router P.
D. Add the no-vrf-propagate-ttl statement to the VPN-B routing instance on PE2.
Answer: A, C
An LDP Layer 2 circuit between PE1 and PE2 is not passing traffic. Both PE1 and PE2 show the circuit state as VM – – vlan id mismatch.
Referring to the exhibit, which action will solve this problem?
A. Configure interfaces PE1:ge-1/071.5 and PE2:ge-1/1/1.6 with the output-vlan-map pop parameter.
B. Configure interfaces PE1 :ge-1/0/1.5 or PE2:ge-1/1/1.6 with the output-vlan-map swap parameter.
C. Configure the LDP Layer 2 circuit with the no-control-word command on PE1 and PE2.
D. Configure interfaces PE1 :ge-1/071.5 and PE2:ge-1/1/1.6 with the output-vlan-map swap parameter.
Referring to the exhibit, you have configured an L3VPN that connects Site-1 and Site-2 together, but the BGP routes are being hidden on the PE routers. The topology in this scenario is shown below.
Site-1 > PE-1 > P-1 > P-2 > PE-2 > Site-2
Which two acttions would allow communication Site-1 and Site-2? (Choose two.)
A. Disable CSPF on under MPLS on P-1 and P-2.
B. Configure DGP on P-1 and P-2.
C. Enable RSVP for all interfaces on P-1 and P-2.
D. Enable LDP for all interfaces on all routers.
Answer: C, D
A layer 2 circuit (RFC 4447) is established between two PE routers to provide connectivity between two customer sites. Which two statements related to this deployment are true?
A. Kompella encapsulation is used in the data plane communications.
B. LDP must be used for the control plane communications
C. BGP must be used for the control plane communications.
D. Martini encapsulation is used in the data plane communications.
Answer: B, D
Referring to the exhibit, which router will be the RP?
A. R4 for all groups
B. R1 for group 184.108.40.206 and R4 for all other groups
C. R1 for all groups
D. R4 for group 220.127.116.11 and R1 for all other groups
You must ensure that r1’s IPv4 loopback address exists in r3’s inet 0 routing table
Referring to the exhibit, which statement is true?
A. An IPv4 unicast realm can be enabled on each router.
B. A policy can be configured on M to redistribute 172.16.100.1/32 into OSPFv2, which would cause r3 to eventually learn the route and place it into inet0.
C. A RIB group can be configured on r3 to copy that route into inet 0 because 172.16.100.1/32 exists in r3’s inet6.0 table
D. A policy can be configured on r1 to redistribute 172 16 100 1/32 into OSPFv3, which would cause r3 to eventually learn the route and place it into inet 0.
New Updated JN0-661 Exam Questions JN0-661 PDF dumps JN0-661 practice exam dumps: https://www.dumpsschool.com/JN0-661-exam-dumps.html