Try Updated NetApp NS0-180 Exam Questions – [Dec-2017 Dumps]

The success in NetApp Certified Storage Installation Engineer, ONTAP NS0-180 certification exam is very easy . Your success will give you a lot more in form of your professional development in IT Fundamentals,Storage Fundamentals and Installation Engineer. The NetApp NS0-180 exam practice test software comes with money back guarantee, if you fail in the NS0-180 exam, you will not be at risk of losing your money at all. We at, CCNABraindumps provide you most latest and actual NS0-180 exam questions.

Version: 9.1
Question: 1

You are installing two disk shelves on an existing clustered Data ONTAP system. One shelf is a DS2246 that matches the other shelves in a stack. The other shelf is also a DS2246 but it contains all solid state disks. Both disk shelves must be added to the same stack.
How would you install the disk shelves?

A. Install the solid state disks first, then the DS2246 shelf so that the solid state disks are as close to the top of the stack as possible.
B. Install the spinning disk shelf first and put the solid state disks at the end of the stack.
C. Advise the customer that solid state disks cannot exist on the same stack as spinning disks.
D. Move the disk drives around to create two shelves that are half solid state and half spinning drives.

Answer: A

Explanation:
As SSDs are faster they should be put close to the top of the stack.
Incorrect: Not C: The DS4246 disk shelf only supports high-capacity disk configurations and “Mixed Shelf” SSD configurations that combine SSDs with high-capacity disk drives. Not D: Place the SSD disk shelves in a separate stack other then the disk shelves containing SAS disks. Because the potential high IOPS, thus high SAS I/O bandwidth utilization, we don’t want to be limited by our backend SAS I/O. As NetApp states; “Full SSD shelves (24 SSDs) are best placed in their own stack”.
Reference: Clustered Data ONTAP 8.3, Physical Storage Management Guide, page 25

Question: 2

Upon completion of an installation, you have begun failover/giveback testing. You notice that when node-02 has been taken over by node-01, node-02 will not respond to ping requests.
Which statement describes what is happening?

A. The controller is down and has been taken over by the partner, this is normal behavior during a failover.
B. The controller that is up, node-01, does not have partner statements in the /etc/rc file.
C. The controller that is down, node-02, does not have partner statements in the /etc/rc file.
D. There are no ports in the LIFs’ broadcast domain that are linked.

Answer: A

Question: 3

New Updated NS0-180 Exam Questions NS0-180 PDF dumps NS0-180 practice exam dumps: https://www.dumpsschool.com/NS0-180-exam-dumps.html (65 Questions)

What happens to the NTP configuration in clustered Data ONTAP 8.3 when a node joins a cluster?

A. A node that joins a cluster has a separate NTP service.
B. A node that joins a cluster automatically adopts the NTP configuration of the cluster.
C. A node that joins a cluster must be manually configured in the NTP.
D. A node that joins a cluster must reboot before running the NTP service.

Answer: B

Explanation:
A node that joins a cluster automatically adopts the NTP configuration of the cluster.
Reference: How to configure and troubleshoot NTP on clustered Data ONTAP 8.2 and later using CLI
https://kb.netapp.com/support/index?page=content&id=1014787

Question: 4

You are assigned to install five DS2246 with twenty-four 400 GB SSDs per shelf to a single node system.
According the NetApp, which statement is correct?

A. You cannot install five SSD shelves to one System.
B. You need at least two stacks.
C. You need at least three stacks.
D. You can put all shelves in one stack.

Answer: D

Explanation:
Up to 10 shelves are supported per stack for the DS2246, so we one stack is enough as we only have five shelves (DS2246s).
Reference: Making the Move from FC to SAS Storage
http://www.netapp.com/as/communities/tech-ontap/tot-fc-sas-1101-as.aspx

Question: 5

Which three types of interface groups are supported on NetApp storage systems? (Choose three.)

A. single mode
B. HA interconnect
C. IPspaces
D. static multimode
E. dynamic multimode

Answer: A,D,E

Explanation:
You can create three different types of interface groups on your storage system: single-mode, static multimode, and dynamic multimode interface groups.
Reference: Types of interface groups
https://library.netapp.com/ecmdocs/ECMP1196907/html/GUID-EFA72201-E035-41E2-AC53-CD81A472B5ED.html

Question: 6

You have just configured the customer’s first SVM with a LIF IP 10.0.0.10/24. The customer’s DNS IP address is 172.16.0.250 and you are unable to ping it from the NetApp storage system, but you are able to ping the gateway and everything else works.
In this scenario what is the problem?

A. You need to have the DNS server on the same subnet as the LIF IP address.
B. You need to add a static gateway to the LIFs routing group.
C. You need to have the customer check the cable.
D. You need to add an IPspace and domain broadcast to the port.

Answer: D

Explanation:
A broadcast domain resides in an IPspace, and it contains a group of network ports, potentially from many nodes in the cluster, that belong to the same layer 2 network. The ports in the group are used in an SVM for data traffic.
Reference: Clustered Data ONTAP 8.3, Network Management Guide, page 8